Magnum-venus-plastech System One FRP 4101-00-01 Manual do Utilizador

FRP SystemOneGelcoatMaintenance & Repair ManualFRP SystemOne 4101-00-01 Gelcoat Metering PumpPart No. M6704-4-1Revision 04.09.01MAGNUM VENUS PROD

FRP SystemOneGelcoat7Fig. 4.1Offeset intake and outletports one flat hex asshown in figure.14. Install the 7304-2-1 (Piston Seal) onto the threaded en

FRP SystemOneGelcoat820. Place the 9201-1-7 (7/32” SS Ball) down inside the 4101-15-1(Check Valve Body) through the double threaded side.21. Install t

FRP SystemOneGelcoatFRP SystemOneCS1S1Gelcoat CatalystSurge Chamber ReassemblyChapter51. Install a 7301-9-013 (O-Ring) over the threaded end of the410

FRP SystemOneGelcoatFRP SystemOne GelcoaterParts DrawingsChapter610

FRP SystemOneGelcoat11MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoatThe parts for this repair kit areincluded in the Metering PumpRepair Kit, PN 6702-5-112

FRP SystemOneGelcoat13MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoat14

FRP SystemOneGelcoat15MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoat16

FRP SystemOneGelcoatFRP SystemOneMaintenance & Repair ManualGelcoat Metering Pump Module© 2001 Magnum Venus Products Manual Part No: M6704-4-1MVP

FRP SystemOneGelcoat17MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoat18

FRP SystemOneGelcoat

FRP SystemOneGelcoat

FRP SystemOneGelcoat© 2001 Magnum Venus Products Manual Part No: M6704-4-1MVP Manufacturing/SalesPhone: (253) 854-2660 (800) 448-6035Fax: (253) 854

FRP SystemOneGelcoatCHAPTER 1 - GETTING STARTEDTools RequiredCHAPTER 2 - INSTRUCTIONSDisassembly of Metering PumpCHAPTER 3 - INSTRUCTIONSDisasse

FRP SystemOneGelcoat1FRP SystemOneGelcoat Metering PumpGetting StartedTools Required1. 1” Open End Wrench2. 3/4” Open End Wrench3. 5/8” Open End Wrenc

FRP SystemOneGelcoatFRP SystemOneDisassembly of MP.057S1 GelcoatMetering Pump2Chapter21. Remove 4101-15-1 (Check Valve Body) from 4101-14-1 (OutletBod

FRP SystemOneGelcoat7. Remove and discard the 9201-1-5 (5/32” SS Ball).8. Remove and retain the 4101-3-1 (Piston Rod Spring).9. Unscrew the 4101-11-1

FRP SystemOneGelcoat4FRP SystemOneCS1S1 Gelcoat Catalyst SurgeChamber DisassemblyChapter31. Loosen the 4101-18-1 (Jam Nut), and remove the 4104-8-1(Ga

FRP SystemOneGelcoatFRP SystemOneReassembly of MP.057S1Gelcoat Metering PumpAssembly Procedures:1. Install 7301-9-013 (O-Ring), and 4101-8-1 (Inlet Tu

FRP SystemOneGelcoat65. Thread the 4101-1-1 (Lock Nut) onto the 4101-2-1 (Cylinder) until itbottoms on the Cylinder shoulder.6. Install a 7301-9-013 (