Magnum-venus-plastech System One FRP 1300-1-1 Manual do Utilizador

FRP SystemOneGelcoaterOperation ManualMAGNUM VENUS PRODUCTSFRP SystemOne1300-1-1 GELCOATER OPERATION MANUALPart No. M1300-1-1Revision 04.26.01

FRP SystemOneGelcoaterr3. Lock the gun in the open position. Remove the pivot pin from thecatalyst slide arm linkage. Use the slide arm to hand prim

FRP SystemOneGelcoater8Pressurizing Fluids:The SystemOne Gelcoater Unit is standard with a safety override valve.This valve opens and closes the air s

FRP SystemOneGelcoaterDaily Maintenance1. Drain water trap.2. Daily shutdown should include, remove air-assist tip and staticmixers from housing and c

FRP SystemOneGelcoater10GunGun maintenance: Turn the pump regulator pressure to zero. Openup the ball valve at filter to relieve gelcoat fluid pressu

FRP SystemOneGelcoater11IT IS ADVISED THAT THE FOLLOWING COMPONENTS BE REBUILTAFTER 6-MONTHS OF USE IN A 8-HOUR, 5-DAY A WEEK SHOP.Catalyst Pump1. Min

FRP SystemOneGelcoater12Chapter5FRP SystemOneParts Drawings

FRP SystemOneGelcoater13MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater14

FRP SystemOneGelcoater15MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater16

FRP SystemOneGelcoaterUnit InformationUnit #Type Of:Power CylinderMetering PumpGunFluid SectionFRP SystemOneGelcoater Operation Manual

FRP SystemOneGelcoater17MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater18

FRP SystemOneGelcoater19MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater20

FRP SystemOneGelcoater21MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater22

FRP SystemOneGelcoater23MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater24

FRP SystemOneGelcoater25MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater26

FRP SystemOneGelcoaterCHAPTER 1 - QUICK LISTStart UpInstallation & SetupCHAPTER 2 - GETTING STARTEDInstallation & SetupPre-Operation Check

FRP SystemOneGelcoater27MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater28

FRP SystemOneGelcoater29MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater30

FRP SystemOneGelcoater31MAGNUM VENUS PRODUCTS

FRP SystemOneGelcoater32

FRP SystemOneGelcoater

FRP SystemOneGelcoater

FRP SystemOneGelcoater

FRP SystemOneGelcoater

FRP SystemOneGelcoater1FRP SystemOne GelcoaterNOTE: These instructions include resin and catalyst pressurizationprocedures. To avoid equipment malfun

FRP SystemOneGelcoater© 2001 Magnum Venus Proeducts Manual Part No: M1300-1-1MVP MagnumPhone: (727) 573-2955Fax: (727) 571-3636Email: [email protected]

FRP SystemOneGelcoater2FRP SystemOne GelcoaterQuick List InstructionsInstallation & Setup1. Unpack unit &components2. Place unit & stand p

FRP SystemOneGelcoaterChapter21. Remove unit from crate.With the crate lying flat, open the top panel and remove thecomponents:a. Floor mount assembly

FRP SystemOneGelcoater4. Mount catalyst jug bracket.a. Attach the Catalyst jug bracket to the base of the catalyst pumpslide drive support.b. Mount th

FRP SystemOneGelcoater9. Make hose connections.a. Connect the black resin hose from the gun to the outlet fitting onthe resin filter.b. Connect the ca

FRP SystemOneGelcoaterrelief valve located on the top of the lid. Set flush tank pressure at50 to 60 psi.2. Push the flush valve on the side of the g