Magnum-venus-plastech PATRIOT SSB Commissioning and instruction Manual do Utilizador

SSB_Auto Instructions Issue 05 Page1 SSB Commissioning and instruction manual Automatic head version design only To enable quick understanding of

SSB_Auto Instructions Issue 05 Page10 A/ In dispense mode there is no need to flush the mixing head as this is by-passed and not used for dispense o

SSB_Auto Instructions Issue 05 Page11 The catalyst inlet filter located within the catalyst bottle should be removed and cleaned in solvent and wate

SSB_Auto Instructions Issue 05 Page12 9.0 Resin pump 100 cc Resin Pump

SSB_Auto Instructions Issue 05 Page13 9.1 Resin pump service. In order to service internal resin pump seals first pump out any resin from intern

SSB_Auto Instructions Issue 05 Page14 10.0 Catalyst Pump - Catalyst pump parts drawing

SSB_Auto Instructions Issue 05 Page15 10.1 Catalyst pump piston seal. The SSB model is designed with a new type of internal Piston valve. This new

SSB_Auto Instructions Issue 05 Page16 Notes. If the piston seal assembly is not assembled as per the instructions concerning the lost motion t

SSB_Auto Instructions Issue 05 Page17 Do not attempt to remove the top piston rod clevis (4278) from the shaft as this is permanently thread locked

SSB_Auto Instructions Issue 05 Page18 11.0 Injection Head and Mixer assemblies

SSB_Auto Instructions Issue 05 Page19 Catalyst Auto valve assembly. - CAV Servicing notes. The catalyst auto valve needs little servicing as

SSB_Auto Instructions Issue 05 Page2 Health & Safety - General over view of important health and safety issues relating to this machine The f

SSB_Auto Instructions Issue 05 Page20 The valve should only need servicing if air or catalyst is noted to weep from between the air cylinder 6078 an

SSB_Auto Instructions Issue 05 Page21 Auto Resin Valve assembly - RAV Caution Note. For safety reasons - Always ensure that the Resin Auto valv

SSB_Auto Instructions Issue 05 Page22 11.1 Head Mixer and Mould pressure Guard (MPG)

SSB_Auto Instructions Issue 05 Page23 12.0 Solvent pump NEW SP3 (Jan 2003 onwards) Note. With the introduction of the new Stainless Steel SP3 So

SSB_Auto Instructions Issue 05 Page24 12.1 SP3 assembly

SSB_Auto Instructions Issue 05 Page25 Resin Gel Alarm – RGA The RGA unit is set to operate only when injection takes place. On inj

SSB_Auto Instructions Issue 05 Page26 insufficient volts the lower yellow light will flash. If this condition is observed immediately renew the batt

SSB_Auto Instructions Issue 05 Page27 8 7 9 8 A 9 B 10 C 12 D 15 E 20 F 25 SSB Auto Machine Doctor This table provides typical fault condi

SSB_Auto Instructions Issue 05 Page28 5. Catalyst head valve has not fully opened when commanded by injection command Check both the resin auto va

SSB_Auto Instructions Issue 05 Page29 weak 2.NRV2 blocked or broken Check NRV2 internal seat and spring 3.Mixer partially blocked Check mixer

SSB_Auto Instructions Issue 05 Page3 PDC reset button - PDC count set button Recirculation Inject Fl

SSB_Auto Instructions Issue 05 Page30 Additional SSB connections

SSB_Auto Instructions Issue 05 Page31 Machine air circuit

SSB_Auto Instructions Issue 05 Page32 Appendix Image files Applicable to Manual NON auto SSB model option H

SSB_Auto Instructions Issue 05 Page4 Before proceeding to connect air supply ensure for safety reasons the following steps are taken. Refer also to

SSB_Auto Instructions Issue 05 Page5 3.2 Fill Solvent cleaning tank with at least 5 litres of Acetone (see caution note below) Maximum 20 litres. Us

SSB_Auto Instructions Issue 05 Page6 To do this ENSURE ratio arms are in position as illustrated. This position is when the ratio drive is at the lo

SSB_Auto Instructions Issue 05 Page7 3.17 Turn solvent isolation valve Open 90º (in line with valve flow) and operate (Pull) solvent Air flush contr

SSB_Auto Instructions Issue 05 Page8 Notes a/ Additional lengths of 10mm pipe are available from Plastech. B/ The Turbo Autosprue 4mm red signal pip

SSB_Auto Instructions Issue 05 Page9 green start button will now pop out to the off position. Flushing can now be carried out as before. Finally