Magnum-venus-plastech GMX-2000 GRANIT COAT GUN Manual do Utilizador

MAGNUM VENUS PLASTECH GRANITE COAT GUN REPAIR MANUAL REV: 3/29/2007 GRANIT COAT GUN INTERNAL MIX GMX-2000

10 PREPARATION AND PRIMING OF PREVIOUSLY USED (shut down) SYSTEM 1. Slowly open main air. 2. Material Pump: (be sure catalyst pump is disengag

11 SHUT DOWN PROCEDURES FOR SPRAY EQUIPMENT 1. Trigger gun until pump shaft is in the full down position (at bottom of stroke position). 2. Eng

12 TESTING SPRAY PATTERN 1. Testing of your spray pattern should be performed away from original part. Use paper or cardboard to check the followin

13 DISASSEMBLY OF GRANITE GUN GMX-2000 Caution: Always remove fluid pressures before working on the unit. WARNING: Be careful not to bend the catal

14 Flush Valve Disassembly (5104-01-01) 1. Remove and discard the Flush Valve Split Seal (5104-21-1) from the Flush Valve Body (5104-24-1) 2. Remo

15 ASSEMBLY OF GRANIT COAT GUN GMX-2000 Flush Valve Assembly (5104-01-01) See Drawing Flush Valve Assembly (5104-01-01) for reference 1. Install

16 13. Install new O-Ring (O-S-012) on Catalyst Needle Housing (CPR-2003-02) and thread into Gun Block 14. Install new O-Ring (O-S-012) on Seal Ho

17 Gun Adjustment and Start Up 1. Make sure trigger and trigger bar are no worn, loose or damaged before adjusting gun or needle guides. 2. Adjust

18 PARTS DRAWINGS: GMX-2000 GRANITE COAT GUN ASSEMBLY DRAWING GMX-2000-SK SEAL KIT – GRANITE COAT GUN 5104-03-01 INJECTOR ASSEMBLY 5104-01-

2

20

21

22 TROUBLE SHOOTING: Catalyst Problems: 1. Catalyst leaking around Needle (inside Needle Housing CPR-2003-02)  Replace O-Ring (O-S-006) on Ne

23 Resin Problems: 1. Resin leaking around Needle (inside Packing Nut MG-1022)  Tighten Packing Nut (MG-1022) a little  Replace Packing Seal (MA

24 1. Material leaking from around the mix chamber  Replace Mix Housing Seal (O-S-016) or Mix Housing Seal (5104-12-1)  Replace Catalyst Injecto

25 Corporate HQ/Mfg. Manufacturing/Sales 5148 113th Ave. 1862 Ives Ave. Clearwater, FL 33760 USA Kent, WA 98032 USA Ph: (727) 573-295

3 TABEL OF CONTENTS: 1. EQUIPMENT SAFTY 2. DISASSEMBLY OF GRANITE COAT GUN 3. ASSEMBLY OF GRANIT COAT GUN 4. PARTS DRAWINGS 5. TROUBLE SHOOT

4 EQUIPMENT SAFETY Injection Hazard • DO NOT POINT THE GUN AT ANY PERSON • NEVER LOOK AT THE GUN FROM THE FRONT (NOZZLE END) • NEVER trigger an

5 PUMPING SYSTEM SAFETY INSTRUCTIONS Use MVP replacement parts to assure compatible pressure rating. Read ALL warning and safety instructions carefu

6 pliable and to keep material drag-thru soft. Material drag-thru that is allowed to harden, will score the piston rod. This will create excessive

7 Important safety information – The below potential hazards may cause an injury or loss of life HAZARD CAUSE SAFEGUARD Fire Solvent and coating

8 WARNING Static Spark Can Cause explosion resulting severe injury or death. Ground pump and pumping system Injection Hazard Any material injected in

9 PREPARATION AND PRIMING OF “NEW” SYSTEM 1. Be sure all air regulators are turned completely to the left, shutting off air to the components. 2